Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
added to your cart!
Slim, extremely light weight batteries based on Lithium Ion chemistry. Each cell outputs a nominal 3.7V at 1250 mAh and is IE…
These are very slim, extremely light weight batteries based on Lithium Ion chemistry. Each cell outputs a nominal 3.7V at 850…
This is a very small, extremely lightweight battery based on Lithium Ion chemistry, with the highest energy density currently…
No, these aren't some sort of weird, AA battery, this is actually a 18650 Lithium Ion Cell. These round high capacity cells h…
These are very slim, extremely light weight batteries based on Lithium Ion chemistry. Each cell outputs a nominal 3.7V at 200…
The SparkFun Nano Power Timer will run while only consuming minimal power (approximately 35nA) and turn your project on after…
This is a very small, extremely light weight battery based on Lithium Ion chemistry. This is the highest energy density curre…
If you need some juice, this 6Ah Lithium Ion Battery is for you. These are very compact batteries based on Lithium Ion chemis…
The SparkFun Soft Power Switch - JST 2mm is like the power button on your laptop, but for your own electronic creations!
Slim, extremely light weight batteries based on Lithium Ion chemistry. With output at a nominal 3.7V at 1500 mAh and is IEC62…
The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a Li…
This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel j…
A simple Lithium Ion battery charger for 12.6VDC Li-Ion batteries similar to the one we sell.
The SparkFun Soft Power Switch is a passive, hard on/off switch with software feedback and control via USB-C connectors.
This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, slidi…
The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below…
This is the same 18650 Lithium Ion Cell that you know and love, but now includes pre-attached solder tabs! These round high c…
This is a classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing.
This 9V battery holder allows your battery to snap in tight and holds it in place, which is great in situations where you don…
This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been termina…
The Soft Power Switch Mk2 is a passive, hard on/off switch with software feedback and control. In other words, it's like the …
CR2032 Lithium metal 3V 250mAh button cell battery. Great for powering low power processors or blink an LED for weeks at a ti…
This is an extremely tiny and light weight battery based on the new Polymer Lithium Ion chemistry.
This USB Power Meter is a versatile tool that can provide voltage, current, capacity, and impedance displayed on the built-in…
This 3xAA battery holder with JST connector puts a nice finishing touch on your battery powered project.
A Lithium battery specifically designed for operating the real time clock (RTC) on the Raspberry Pi 5.
This is a unique two-cell AA battery holde. The 6" (~150mm) cable has been terminated with a JST-PH connector.
This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlig…
10Ah capacity & multiple USB options make this a great option for mobile USB power on your next project.
Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration.
This 3xAA battery holder with bare wire leads puts a nice finishing touch on your battery powered project.
These are your standard 1.5V AA alkaline batteries from Panasonic.
This is an incredibly simple two cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlig…
This is a PCB mount clip to hold a 18650 Lithium Ion Cell battery. Each battery holder is sold in single units, you'll need t…
This is a simple coin cell battery holder that can enclose two CR2032 batteries inside itself, and safely kept closed via two…
This is a through-hole 12mm coin cell battery holder. It's the unit we like to use as RTC backup and SRAM backup for GPS unit…
This 2xAAA battery holder puts a nice finishing touch on your battery-powered project. This holder features a sliding, remova…
Basic 20mm coin cell holder. Posts can be inserted into 0.1" perf board! Holds the common CR2032 type batteries.
These are your standard 1.5V AAA alkaline batteries from Energizer.
CR1225 lithium metal 3V 12mm 47mAh coin cell batteries. Perfect small battery for miniature sensor node applications. Thes…
2500mAh 1.2V Nickel Metal Hydride rechargeable 'AA' batteries. [NiMH technology](http://en.wikipedia.org/wiki/Nickel_metal_hy…
This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, slidi…
These are your standard 9 Volt alkaline batteries from Rayovac. Don't even think about trying to recharge these. Use them wit…
This is the CR2025 20mm coin cell battery. You may be wondering what sets this guy apart from the more common CR2032 coin cel…
The SparkFun Jetson Nano Basic Kit with Battery Pack provides you with all of the essential parts needed to start new project…
This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anyth…
