i have the XCTU software and this device but i cannot get my computer to find the software for this device to connect? any help?

This is a great board, but could be even better with the addition of a reset button!! It's easy enough to make your own, but it's one of those nice-to-have features!
clokey - Your question is fairly old, but in case you're still wondering - you probably want to use a different board for programing your Arduino. It can be found here: https://www.sparkfun.com/commerce/product_info.php?products_id=8772. (You can actually do some fancy stuff and use the board on this page to program an Arduino remotely, but I get the feeling that isn't what you're looking for.)

Some users have posted messages indicating they've had trouble using the long-distance, Pro version XBee modules with XBee Explorer. Here are some tips that might help.

Before USB device enumeration takes place, only 100 mA is supplied to each device on the USB bus. During device enumeration, a device can request more than that (up to 500 mA). Not all USB ports and hubs can honor that request, especially if you're using an external hub that is powered by a USB port on the PC. When in doubt, use a heavy duty hub that is powered from an AC adapter.

The USB "power descriptors" in the XBee Explorer's FT232RL chip are configured to the factory default value of 90 mA. This works fine for the regular XBees, but not for the Pro versions, since they need more power when transmitting. To make the FT232RL request more than that from the USB hub or PC port, you can run the free FTDI ft_prog.exe utility to reconfigure the FT232RL power descriptors. This app note describes how to install and use ft_prog.exe - http://www.ftdichip.com/Support/Documents/AppNotes/AN_124_User_Guide_For_FT_PROG.pdf.

The app note says you need to install their special D2XX drivers but on 64-bit Windows 7, I found that I didn't have to do that. All I did was to launch ft_prog.exe, made it scan my USB ports to find the FTDI device, and changed the "Max Bus Power" value under USB Config Descriptors from 90 to 265 mA, since the Series 1 XBee Pro 802.14.5 module I'm using draws 250 mA when transmitting and the FT232RL itself draws another 15 mA. Some of the really long-distance, high-power XBee modules may require more than that.

After unplugging and replugging the XBee Explorer to confirm that it retained the new power setting, Windows displayed the usual "Installing device driver" pop-up message and said it successfully installed a driver for the new device. This is to be expected because when the FT232RL's descriptors change, Windows thinks it's a new device.

Hope it helps, WattNode guy

If I solder 0.1 headers to the bottom and plug it into a breadboard, can I use the board without USB to connect a microcontroller and an xbee, assuming I provide power. I just want both options for USB and for breadboarding the xbee without buying two different breakout boards and I'm hoping that is an option.

deen, these XBee modules program though the same serial connections that rcv and xmit data, so in short, yes this will do the trick.
Sparkfun guys, I know there are 150 in stock, but maybe you could make a USB key version of this that slides into your port like the new AVR board. MiniUSB is nice, but I have cords everywhere and boards this small tend to not stay put when there is any stress/movement of the cable. I would love this type of thing anytime you make a USB board, because a simple USB extension cable could always turn it into a tethered board.
Thanks

Just so you know, you cannot use this interface board with the new Digi XBee S3B module. The USB Explorer has an RSSI LED on Pin 6. On the S3B module, pin 6 is a config pin. The LED pulls that pin low and forces the module into a diagnostic mode. The only way to work around this is to physically remove the RSSI LED or resistor.

And honestly, there's no need for an RSSI LED on these boards. You are not going to be able to tell the difference between a strong or weak signal using an LED.

In addition to using the board as an USB to XBee connector, I would like to use it as the basis for a stand-alone XBee application. Thus I have to supply battery power for the XBee.
As the XBees can operate with supply voltage of 2.8 - 3.4 V is it possible to connect a 3V battery pack (2x AAA) directly to some of the pins/holes of this board?

I was all excited to start playing around with my new XBee kit including this part, only to discover that the X-CTU software isn't 64-bit compatible. No Vista or Windows 7 support. :( Now I have to mess around with an emulator or some nonsense... sigh
No Linux or Mac support either.

I designed a new version and sent my Eagle Files to Sparkfun.
http://img.photobucket.com/albums/v232/BillFleming/XBee-Explorer-v16.png
It has a reset switch and easy access TX, RX, 3.3V, GND, and 5V on the front to use this for other devices. I think you could attach right angle headers to it.(and still see the LEDs)
I also put all of the silkscreen and labels on the top only. I think if you hook this into a breadboard it will be easier to hook up pins now. (You can't see the pin labels on the bottom when you plug this into a breadboard)

I've had a couple of these things lying around, and only just now connected one to my WinXP machine. I don't have anything currently plugged into it.
This thing takes the old "+++AT" commands. I've discovered a few of them (ATZ - reset, ATE - echo off, ATD - dial), but I can't figure out where to find the whole command set. After all, when this thing has the XBee plugged into it, who's to say where the AT commands wind up - on this board or on the XBee?

This board being a USB board, I expected a USB mini B connector. The mini B was not what my boards had. I went down and found a similar looking connector and it worked. Now I'm wondering why they used a PS3 (4) charging cable instead of the standard mini B??? I think the description of this item should give more information about the cable it requires. I've never seen a cable like this before. Maybe SparkFun sells these cables. I have not looked to see. But, I thought I might let people know about the cable.

I have the Roving-Network rev3 unit (https://www.sparkfun.com/products/10822) and this unit. With these two units i wanted to setup a base station to control a Arduino.

But it seems not to work as i cant get in contact with the WIFI unit true the serial interface. Anny suggestions?

We organized a workshop using XBees, Arduinos and XBee Explorer USB. Five of the explorers broke and I don't know the reason. Could it be that the the participants were powering the XBee Explorer using both the USB and the Arduino 3.3V pin simultaneously? I need to find the explanation to prevent this from happening again. Thanks :)

I have an old board dating pre Aug 2010, how much power are they good for ?

Can you make it slightly longer? Just get yourself an XBee wifi and find out how much longer. This current design makes the USB-mini connector butt against the wifi module. I can't insert all pins of the XBee wifi into the headers.

Do I need to buy this even if I have a Series 1 XBee, since it is written in the guide “they don’t need to be configured”?

Does anyone know if the XBee product line can be used as an 802.15.4 packet sniffer? I'm curious if this could be used to debug another 802.15.4 product.

Can someone confirm if this would work with the RN-XV WiFly Module?

hi it has 3.3 voltage regulator i want to connect XBee Explorer USB with 5v and connect xbee to XBee Explorer USB(3.3v)

Has this been tested at 500mA output current? The MIC5219 would be dissipating ~0.85W at 500mA output [(5-3.3)*0.5]. Theta-ja is 220C/W, which would lead to about a 190C temp rise. I don't know what the duty cycle of a XBee pro going "full bore", but any design assuming the 3.3V regulator can sustain 500mA from a 5V input will quickly release the smoke.

I have a question.

I bought the Xbee explorer USB and have a project that works well with Arduino. When I Serial Monitor, Xbee USB explorer automatically opens the Serial COM port lights and lamps Rx and Tx.

When you step into the LABVIEW the door does not open automatically.

Help me please it is urgent!

Thank you!

Philip

Note there is now XCTU software for the Mac:

Hi, is normal that this board can't read an old XB24-ACI-001 xbee module?, or my module is dead, because the X-CTU software marks UNKNOW modem.

How do you reference pins back to xbee series 1? I dont get it...

pin 6&7 refers to PWM0&PWM1 what is the equivalent on this board? RSSI&DI011?

Is anyone else having issues looking at the schematic? When I click the link in the Documents section above, all that shows up on the PDF is a few dots and circles (and a couple of other symbols.

Can someone please confirm this acts as a logic converter, ie: it automatically steps up / down the rx / tx to 3.3v in or 5v out to arduino so I don't have to use a separate converter?

Use the board all the time but I am wondering how I can use it just for talking to the Arduino with serial. I have tried to put the Dout and Din on to the Arduinos Tx0 and Rx0 ports and it doesn't work. Does anyone have any idea what I'm doing wrong??

Would anyone be able to give an explanation on how to reset this explorer in X-CTU. I have soldered wires onto both RST and GND pins to create a short wire to reset it, but no luck. Also tried on a bread board with a switch and without, and still no success.

This board actually has a ground plane in the "keep out" area from the Xbee data sheet. That means this board will have somewhat worse range than a board that adheres to the guidelines, especially for boards with chip antennas!

Hey everybody, I am working on a project which is about the classroom response system, and for the receiver part i'm gonna use a Xbee and this Xbee USB explorer. But i wanted to know how can i send the data received to the computer. Do i have to use any program or software ? the X-CTU can handle it ? Thank you

I just bought a digi XBee ZB S2 ZigBee Module. i just want to know if it works with Sparkfun's XBee Explorer USB(WRL-08687). Also can the XBee Explorer USB be fixed/ soldered on a bread board, vero board etc.

Thanks so much

I am new with Xbee and I am using X-CTU, can’t figure out why it responds only to AT command: +++ (OK) but not any other AT command I send to it. Any idea? Cheers! Alessandro

Hi! I'd like to match the miniUSB pinouit in WRL-08687 to the miniUSB pinout in DEV-08772 and I can't find the way to do it in the squematics (there is 5 wires instead of 4, such as the squematics says). Could anybody help me? I need it for my degree final project. Thanks a lot!

Hey every one ... i guess i am new in Xbee world , i am using the usb Xbee explorer for my 900Mhz xbee , i have a problem that my PC doesn't identify the usb to serial board , and only the power LED is on , where should i start checking ? .... thank you all

I would like to first try cheap RF communication and then Xbee from my laptop to communicate with a robot. Could i purchase this first to communicate by RF similar to 'Breakout Board for FT232RL USB to Serial' device? I checked connection diagram and they do not seem the same but both seem to convert to serial. . . I rather not be redundant and buy both if i do not have to.

I have no problems with this board for Series 1 and 2, but I can't access to my 868RF XBEE modules. Someone know o have a solution for program Xbee 868?

Thanks

When do you guys expect to have these back in stock ? Thanks.

I was able to use this board as a replacement for the FTDI table. All you have to do is connect the respective supply voltage pins (with a different power source from the explorer) on the device you want to connect, then find the DTR and CTS pins and connect them to the DTR and CTS pins on the explorer, and finally connect the Tx and Rx with Din and Dout.

Where is the usb cable that i need to buy???

Shoot! When will these be back in stock?? Just got Christmas SFE money and I can't spend it! Darn....

will the parallax version of this board be able to perform the same as this because diji says to use this one but it never says a thing about any others. I was wondering because I had already bought the other one and was seeing if I made a bad call

I'm using the XBee Wi-Fi PCB Antenna - S6 and I was wondering if this development board will work with it?

I'm working on a project with the 2.8" TFT Touch Shield for Arduino. I"m looking into implementing the XBee to control LEDs wireless, and wireless display the temperature from a temperature sensor on the screen. Can any one give me an idea of what components I need to use ?

Hi, I'm working with this XBee Explorer USB and I found a strange behaviour. When it's connected too much time, it stops to receive data. It is connected in my PC, at the same port, but data doesn't come into the serial monitor. It seems like the Explorer sleeps after some time. I tried with several units and all of them make the same thing. Is there any trick or hardware configuration to avoid this?? I need to receive data each 12 hours. Thanks!

Hey, check out the new book, "The Hands-On XBee Lab Manual," by Jon Titus. It will get you started with 22 experiments that use the XBee Series-1 modules. It covers everything from simple I/O configuration to networks. Examples use the Arduino and mbed modules. Great book, available on Amazon. Titus writes for several engineering magazines, so he knows his stuff. --Mill

Hi,

I know that this might be a silly question but I have been searching for some time and yet I didn't find the answer...

This module is needed so to program the Xbee module right? Also, what software do I need to do so? Any documentation/ tutorial?

Thanks a lot

If I have the 3.3V FTDI Breakout Board that I normally use to program Arduino chips, could I also use that breakout board in place of this when needing to configure XBees?

So, with this device, it will be possible to send serial commands to another Xbee device?

I've read lots of people having problems with X-CTU for Linux and Mac. I’ve just found a brand new cross-platform network management suite, and there’s also a free version. I’ve downloaded it from here: http://www.moltosenso.com/#/pc==/client/fe/download.php

So, I've stopped using Wine or Virtualbox. Hope that helps.

curious...when I check the eagle file and the pics on the site...there isn't a connection to the USB ground pin. How does this work?

Well, I started a Windows VM, and used X-CTU and got it to work. I really didn't want to change the FTDI drivers on my Linux box since they work for everything else.

Just received my XBee Explorer and 2 XBee Pro 900 modules. I run Linux, so I figured the first order of business is just to establish a connection. I plugged one of the modules into the Explorer, plugged in the USB, the power LED is lit, and I see /dev/ttyUSB0. Great.

But after trying minicom, screen, etc, I get absolutely no response.

Anyone have any clues? The XBee Explorer description says that it works with the Pro.

I have been using an XBee Explorer USB (WRL-08687) for about two months without issue. Recently it suddenly stopped working and no longer shows up as a USB device in X-CTU. A second one that I bought later works fine. One minute it was attached to a Linux machine reading Xbee sensor data just fine. The next minute it was dead. Is there any way to revive it?

three questions:
1) does this board(with transceiver) plug directly into your computer and then transmit the serial codes to the receiving end of the transceivers?
2) my project requires multiple servos, it is actually a robot, so would i hook my arduino UNO and receiver then send the commands?(with the transmitter on the other side, of course)
3)i am new to electronics and wanted to try to use two of SFE's gaming sheilds to control x and y movement of the robt instead of rewriting a code?
Also, could i use the arduino as a comand, sending the movement to the bot, without another Arduino on the bot?

I just received my XBee Explorer USB, but when I plug it into my computer (tried both a macbook and a mac mini) it does not show up as a serial connection in /dev. It is listed as a device connected to the serial bus however. I have searched, but have not found anyone else having this problem. Can anyone point me in the right direction?
Update: Although not mentioned in any tutorial I have read, and I've read several, you will need to install a driver for the FTDI chip to get the USB explorer to work. After installation, the explorer works fine.

Maybe some of you great minds have a hint for me.
Environment & settings:
- 2 XBees, one configured as Zigbee coordinator (AT), other configured as Zigbee end point.
- One Arduino with Xbee shield with simple program echoing what is sent to it.
- One Xbee explorer, attached to
a) Windows XP machine with hyperterminal or
b) Ubuntu 10.04 machine with minicom / picocom / perl program
Problem:
On Windows XP everything works as expected, the (formerly via xctu configured) Xbees work like charm, the link is stable, the sent characters are correctly echoed (in fact the echo isn't exactly an echo...so I can tell if I am fooled by "local echo" feature of the terminal program ;))
On Ubuntu, I can enter AT codes and get the proper (slow...it takes a few seconds) responses (PAN ID, the ID in the network, the joined network) but I don't get any response (the echo stuff) from the other Xbee.
The tx LED shows activity whenever I hit a key in the terminal program. So far (on the Ubuntu m

Is this board needed to do specific functions with the XBee? Or can all the functionality of this board also be done with an Arduino?

How do I get this working with X-CTU on my Windows 7 (32-bit) PC? I have no problem using X-CTU on COM port 3 with the ladyada Xbee Adapter and USB cable. I can program the Xbees just fine that way. But When I plug the XBee Explorer into my PC, X-CTU doesn't see it. I clicked on the link above that says USB FTDI Drivers, but I wasn't able to follow the documentation because it was so complex. I downloaded CDM20814_WHQL_Certified.zip from www.ftdichip.com/FTDrivers.htm, but there is not install program.

Here is a blog post I did on the using the Xbee explorer with an Arduino with the SparkFun Xbee Shield. I use this setup for controlling my pan tilt antenna for my UAV.
http://fisherinnovation.com/i/2011/06/12/simple-xbee-communication-with-arduino/

I've read the tutorials on how to use this to do wireless bootloading. All of them talk about putting a jumper on the XBee Explorer.
So, does this mean if I want to have a Fio talking with a host computer wirelessly, I'd need two XBee Explorers - one for programming (with the jumper) and one for regular communication (without the jumper)? I suppose a switch could be installed.
Am I understanding this correctly?

Hello! Which FTDI driver to use? There are two drivers, VCP (Virtual COM Port) driver and the D2XX (Direct USB via DLL) driver. I want to connect my laptop to the xbee module. Thanks!

Hi,
Is it possible to use this board to program the Programmable XBee Pro ZB?
http://www.digi.com/products/wireless-wired-embedded-solutions/zigbee-rf-modules/zigbee-mesh-module/xbee-zb-module.jsp#overview

I wrote a review of the ladyada vs this adapter.
This adapter is definitely simpler to use, and it's nice that it's prebuilt.
I've found the RX/TX LEDs essential when you're blind flashing a module.
The only thing this is missing is a reset button, which is essential for blind flashing and flashing modules that go to sleep (ZB END DEVICE AT).
I wrote a picture of a hacked up way I did that:
http://marc.merlins.org/perso/arduino/2011-05.html#PC-Breadboard-Xbee-Adapters_-Sparkfun-and-Adafruit
but I would have saved a lot of time figuring it out if it had come pre-installed.
The module is also missing an ASSOC LED, which can come handy.
But please, just add a reset button or jumper, this module is great for module flashing and programming otherwise.

Hi
I bought one of these and it works great. I was about to buy the adafruit adaptors but noticed that on this board there are a number of header pads at the opposite end to the usb connector and that these pads provide RSST, RX, TX, 5V, GND.
Now Im thinking I could use this board to connect my zigbee device to my quadcopter. Do those pins provide the right stuff, saving me the need for another board ?
regards

Which FTDI driver to use? There are two drivers, VCP (Virtual COM Port) driver and the D2XX (Direct USB via DLL) driver.

I just started to use two of these boards a few weeks ago. A curious thing has happened in the past week: the power LED (next to the mini USB connector) on one started flickering a few days ago and the LED no longer illuminates now. But the XBee and communication to/from the XBee seems to be working OK. The power LED on the second board is flicking also but remains mostly fully illuminated (for now).
Both devices are powered from a USB hub (powered from the PC). I think there is plenty of power available -- I don't have any problems with the other peripherals on the bus.
I'm hoping this is just a dud LED or LED resistor and nothing more serious.
The date on the PCB is 10-8-08.

This is a great board, but I had an idea when working on my current project -- add the circuit necessary to charge a single cell LiPo, and a place to connect a jst connector or solder in two battery leads. I'm making a tiny (as much as I can) xbee sensor, and currently I have to add another board to it. Putting a charge circuit on this would make a self-contained xbee sensor node. It's already regulating, so I wouldn't think it to be too hard. just plug it into the usb to charge or to reconfigure the xbee.

So, all in all this is a good breakout board. One warning though: I've been able to use it with normal XBees (both series 1 and 2), but I had some trouble with a couple of XBees Pro S1 due to the fact that the board doesn't carry a reset button. To update / restore the firmware on the XBees via the X-CTU Win software I had to short circuit a couple of pins (pin 5 - RST and pin 10 - GND) directly on the board... you can do that with a simple clip, but hey why doesn't Sparkfun put a small button on the board? It took me a couple of hours before figuring out what I had to do!

I wanted to use the device as a socket for the Xbee on my Breadboard.
I could send/receive Data to/from my µC when I had the Explorer connected to my PC over USB. But when I wanted to run it independent I couldn't receive any characters on the µC anymore. Checking the Rx line with an oscilloscope showed that the RX line had a constant Voltage and didn't send out the charachters that were recieved(The RSSI LED was on when I was typing on the other side but not the RX LED). Yet I saw signals on the line when the explorer was connected via USB.
I had connections to the 5V, GND, DIN and DOUT pins.
Anybody got any ideas why this doesn't work? I guess its something about the FT232. How could I work around this?

For people asking how to reset a bricked XBee, follow the instructions here:
http://www.instructables.com/id/Changing-Xbee-Baud-Rates/step5/Un-bricking-a-frozen-Xbee/
Since the XBee Explorer doesn't have a reset button, take a piece of wire and short the RST pin on the back of the board to GND. You must do this while the X-CTU program displays the message window indicating it cannot connect to the XBee.

The voltage regulator on the board is only rated up to 80mA while the xbee pro versions needs 215mA. Beware if you buy as this board will not have the power needed to make a strong signal. I am having to resolder new voltage regulators to deal with this low amp output. Thanks sparkfun...

Something that was almost a show-stopper for me was the lack of a firmware update utility for Linux (yes, silly I know). So, for anyone else that also happens to use OSS, I would like to introduce xbee-comm . As a warning, I have only tested this on the two "Series 2" radios I have, but if you're feeling lucky you can give it a go with yours.

Can I use the ftdi chip on this board to program an arduino directly, without an xbee inserted?<br />
<br />
If so, can I do this using only the thru-hole connections on the board?<br />
<br />
<br />
I have one of these and I would like to avoid having to buy a ftdi breakout for some standalone arduino projects.<br />
<br />
Thanks

can anyone help me. i need to program 2 xbee pro with this(http://microcontrollershop.com/product_info.php?products_id=2367). and able to revive data from a Atomic IMU 6 Degrees of Freedom. any clues?..

Would this be an effective way to program the HSC08 chip on the new Xbee-Pro ZB Programmable boards? They're my new front runners for my first real microcontoller project. Would the codewarrior suite program through the explorer board, or am I better off wiring up a BDM unit?

I am trying to use this with a Pro 900 (WRL-09098) and it is not working. I have tested the modules in official Digi dev kits and they work fine. The USB Explorer will not transmit or receive. The power light is on, the RSSI light is on and the tx light flashes when characters are sent to it. They just don't get to the other end. Any ideas?

I've been using the USB Explorer for some time now, worked fine. I have two of the XBEE PRO's (XBP09-XSC) Both work fine over the FTDI cable, and are configured properly.
Recently the USB Explorer has stopped working. When plugged in the board has the power light come on, and is recognized as an FTDI (USB Serial Converter) Device. However, when in X-CTU, I select COM3, correct settings and click Test and it simply says "Unable to communicate with modem." Is it possible that I have short-circuited the chip on there? Any other possible tests I can perform? or is it possible to turn the board into an FTDI-Cable board?

I'm trying to use this to configure my Xbee Series 2.5, but I don't know where to begin. I'm new at this sort of thing, but I'm trying to learn. I may sound completely retarded, but what do I do after I take the explorer out of the box and connect the XBee?

I think it's misleading to list the high power XBee modules that draw too much power to work with this board, as it implies that this board will work with these modules. I also think it would be nice to mention the current limitations on the product page, or at least include the part number for the regulator used on the schematic.
Note: the same thing can be said for the FIO and the "Regulated Explorer" product.

I've been experiencing the same issue outlined here
http://www.digi.com/support/forum/viewthread_thread,7476
when trying to flash my xbee series 2 device as API using XCTU. The digi thread suggests that it could be an issue with the interface. Can this board be used to flash an xbee module with API firmware successfully... It works with AT mode, and I can't imagine that it wouldn't with API but wanted to ask. Thanks.

I have a 1mw and a 60mw pro Xbee, can I have my 1 mw hooked up to the explorer USB and receive data from the 60?

Does anyone know where I can find the 2mm SMT connectors used on this board to interface with the xbee?

Can I assume that, like the FIO board, the regulator on this is incapable of powering the XBee Pro models?

Any idea if/when these will be restocked?

i just received this board and 2 breakout boards. i knew these things were small but i had no idea. i'll be working with the 300 ft range xbee at first but can't wait to start messing with the higher power versions.

Is it going to be back in stock? I don't see that backorder is allowed... If it's not the case, what are the alternative?
Thanks!

This is a great board and makes experimenting with the xBee very easy. But I do have to agree... a "reset switch" is pretty much necessary when you start playing around with differnet firmware/command sets. Something like the "Mini Push Button Switch sku: COM-00097" would be perfect (leads could be bent flat for surface mount on the bottom of the PCB so you're using a part you alrady stock.

can someone tell whether this can be used to program the Xbee module?? Or is it just to interface to the PC to receive and transmit data??

This is a great board for having play with XBee and quickly setting up communication addresses. But I'm having trouble upgrading the firmware of my XB24 modem. Can this board be used to upgrade using x-ctu?? I want to use my modem for monitoring analog input but from the manual i need firmware ver. at least 10A1 (currently it's 1084).

I think you should add a Arduino compatible connector on the end and a 3V3 regulator as the FIDI chip can only provide 20mA so cannot power a pro.

Can this board be used as a general USB to FTDI board (similar to https://www.sparkfun.com/commerce/product_info.php?products_id=8772)
I have an arduino mini that I want to program and thinking that I can use this board which I have just purchased to play with some XBee parts. Am I barking up the right tree?