Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
1.0M Ohm, 1/4th Watt, +/- 5% tolerance PTH resistor.
This version of the APA102 (or “DotStar”) is an astoundingly tiny, 8-pin, 2020-sized (2x2mm) SMD LED. With an integrated …
Our RedBoards are great. But don't they sometimes seem a little **_BIG_**?! Enter **smôl**, a new range of boards which a…
These are six inch long, 26 AWG jumper wires with breadboard-friendly male connectors on both ends.
This is a 4.7 kOhms, 1/10W, ±1% tolerance SMD resistor.
This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50Ω impedance…
Huge 10mm through-hole LEDs. Mood-light an entire wall!
This is a basic surface mount JST-SH 2-pin right angle connector.
SparkFun Jetson Nano Intermediate Kit with Battery Pack provides you with all of the essential parts needed to start new proj…
Here's a very cool [TFT LCD](https://electronics.howstuffworks.com/lcd4.htm) display with 128 x 160 resolution and 18-bit col…
The Qwiic Transparent OLED HUD is SparkFun's answer to all of your futuristic transparent HUD needs.
This is a class 10, 16GB, micro SDHC card that has been pre-installed with the NOOBS operating system for the Raspberry Pi.
This is a class 10 16GB microSD memory card, perfect for housing operating systems for single board computers and a multitude…
These resonators are +/-0.5% or better from -20C-+80C.
**Replacement:** None. We are no longer selling these. This page is for reference only. These are very small surface mount q…
This is a 240 Ohms, 1/10W, ±1% tolerance SMD resistor.
These LR44 button cell batteries are fairly common but it can be hard to keep them around. They fit our digital calipers, so …
This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins.
Here is a six pin horizontal 1.0mm pitch connector.
The SkyRC B6 V2 is a DC input high-performance, micro-processor controlled charge/discharge/DC/DC converter with battery mana…
The Double Backlit user interface is like the Single Backlit Button, but twice the fun!
This 6 position screw terminal block provides a simple way to connect wires to a single connection point.
This is a 715 Ohms, 1/10W, ±1% tolerance SMD resistor.
This is a 1024 x 600 resolution IPS display touchscreen for the Raspberry Pi.
This is a 3-pin male SMD right angle header.
This is a 2.7 kOhms, 1/10W, ±1% tolerance SMD resistor.
This is a 330 Ohms, 1/10W, ±1% tolerance SMD resistor.
M6E-Nano’s wide RF output range (0 dBm to +27 dBm) is important for the read/write requirements for RFID-enabled printers a…
These 0.1" spaced female headers are perfect for building your own Raspberry Pi B add-on modules. These PTH headers are arran…
Here is a four pin horizontal 1.0mm pitch connector. It is useful if you need something very tiny as a connection. These are …
There is a 3-pin Molex connector on one end, 3-pin JST connector on the other both with 0.1" spacing.
The BMD-34 series are advanced, highly flexible, ultralow-power multiprotocol modules that enable concurrent Bluetooth 5, Thr…
The PiJuice is a fully uninterruptible power supply HAT that will always keep your Raspberry Pi powered.
The SparkFun Variable Load is a quick to assemble kit that has been designed to allow users to draw a specific amount of curr…
This is a 100 kOhms, 1/10W, ±1% tolerance SMD resistor.
This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anyth…
Sometimes referred to as "spade connectors," these quick disconnects are really useful as power connectors in prototyping.
Panasonic FK SMT Aluminum Electrolytic Capacitors feature a high endurance of up to 5000 hours at +105°C and a temperature r…
This is a simple strip of five signal-conditioning Balun Ember Transformers from Wurth Elektronik that allows you to convert …
This is a 680 Ohms, 1/10W, ±5% tolerance SMD resistor.
The ever-popular FTDI USB to UART IC now comes with built-in EEPROM and built-in oscillator! This IC comes in a 28-pin SSOP p…
These are the same RGB LEDs that were used for the old WS2801 breakout board. They're great when you need a lot of color from…
This sleek, red 16GB thumb drive has been emblazoned with our SparkFun Electronics logo and our moniker to Start Something!
This is a 470 Ohms, 1/10W, ±1% tolerance SMD resistor.
The Segger J-Link On Board microcontroller is based on the ARM® Cortex™- M4.
This is a mountable SPDT slide switch --- great for use as a general control switch. The pins are spaced by 3.7mm (0.14"), ma…