Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
This is a foot-long white audio cable that has been terminated with two TRRS connectors at each end. TRRS connectors are the …
A simple slide potentiometer can go a long way. Rated at 10KOhm and 0.1W. Comes with solder tab connections. The pot has an o…
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. …
This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE c…
The 0.3 Watt Volt mini solar panel from Voltaic Systems is a lightweight, waterproof, solar panel designed for 5-7 year outdo…
Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to t…
Do you need that extra push over the cliff? The Small sized GTE (Goes To Eleven) Knob can fit onto potentiometers with a 6mm …
These are very common, high quality BJT NPN transistors made by ST Micro.
2500mAh 1.2V Nickel Metal Hydride rechargeable 'AA' batteries. [NiMH technology](http://en.wikipedia.org/wiki/Nickel_metal_hy…
This is an incredibly simple two cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlig…
The micro:bit Edge Connector - SMD, Right Angle (40-pin) allows you to expand the capabilities of the BBC micro:bit.
This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect fo…
A 200mm MIPI Cable for interfacing the Raspberry Pi Camera Modules with the Raspberry Pi 5.
This relay's coil is rated up to 3V, with a maximum switching voltage of 250VAC, 125VDC. The contacts are rated up to 10A (@1…
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing…
The ATX power connector breaks out the standard 4-pin computer peripheral port for you 12V & 5V devices from one wall adapter…
This is a good quick way to to interface to bare wires.
These 33mm (1.3") spring loaded pogo pins are great for programming and applications where you don't always want headers sold…
The W25Q32FV (32M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins, and power.
This is a translucent silicon rubber button pad with 16 buttons, the same found in our Simon Soldering Kits.
This 3xAA battery holder with JST connector puts a nice finishing touch on your battery powered project.
This is a perfect choice if you are in need of a heavy duty push button! These metal push buttons are a very tough, small, pa…
This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opp…
These Clincher connectors from Amphenol FCI can be used to terminate Flat Flexible Cables (FFCs) to an easy-to-use standard h…
This is a 10-pin header with 2mm pitch that mates with our [XBee socket](https://www.sparkfun.com/products/8272). It can be u…
This is the 100mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards end to end. *** _**smô…
This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anyth…
Holy Wattage, Batman! This Power Resistor Kit comes with 5 each of 5 different 10 Watt resistor values including 1 Ohm, 2 Ohm…
This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1…
This 3ft Category 6 (CAT 6) Ethernet cable is the solution to your internet working needs. With a speed of up to 500MHz you c…
This 2x20 shrouded header has the same number and spacing of pins as a Raspberry Pi so you can easily connect via ribbon cabl…
This is a small device called a [reed switch](http://en.wikipedia.org/wiki/Reed_switch). When the device is exposed to a magn…
The SparkFun Qwiic Alphanumeric Starter Kit comes with two displays, one red and one white, standoffs and screws for mounting…
The ESLOV connector has five pins (one more than standard I2C) for automatically configuring the module and handli…
Plug (three conductors and a ground) & shroud to hack or repair or add a 4-conductor audio jack into your project.
This is a joystick thumb pad very similar to the thumb pads on PlayStation controllers.
These 10 segment bar graph LEDs have many uses. With a compact footprint, simple hookup, they are easy for prototyping or fin…
This a simple breakout PCB for our [2x2 silicone button pads](https://www.sparkfun.com/products/7836). Each LED and button is…
These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it thr…
The µLCD-144-G2(GFX) is a compact and cost effective display module using the latest state of the art LCD (TFT) technology w…
The SparkFun Dual-Port Logging Shield is a Thing Plus/Feather-compatible board which allows you to access your microSD card o…
Embark on a Journey of RFID Exploration with the SparkFun DataLogger IoT RFID Kit.
This is a simple, 220 Ohm, 1/4th Watt, +/- 5% tolerance PTH resistor. Sold as single units.
These are very common, high quality BJT, PNP transistors made by ST Micro. Rated up to 200mA. **Datasheet:** [2N3906](http…
These digital (LH) British Telecom connectors are primarily used by our English friends across the pond but here at SparkFun …
